Z Tactical Comtac I Headset
The Comtac headset is a double-earpiece communications interface with output sound in both ear and a microphone on an adjustable boom.
The Comtac headset is a double-earpiece communications interface with output sound in both ear and a microphone on an adjustable boom.
Double rifle gun case have two main pockets, bigger one have 120 cm long and shorter one have 93 cm long. It also can be used as backpack. Longer pocket have also a sleeve inside that can extend gun case for extra 27 cm.
The gun bag is made of nylon. Thanks to the application of the additional sleeve the cover will without any problem hold a gun that is up to 1300mm long. Inside of the main chamber there are two additional gun mounting bands. Inside the front 620x260mm big pocket we will fit a machinegun. The gun mounting bands are also located in it.
Gun case with two chambers for dual storage/transportation. Main chamber will hold rifle up to 960 mm long (or 1100 mm when utilising the external hood).Secondary chamber will hold a firearm up to 650 mm long.Case also has pockets that allow transporting magazine or other accesories.Case may be transported in ordinary fasion with use of transport handle...
The bag is constructed from durable and tough 600D nylon, which is capable of supporting the weight of two Airsoft weapons with ease. This practical carry case is ideal for any Airsofter who likes taking more than one Airsoft weapon to a skirmish, and keeping all of their gear together in one convenient bag.
Hydration system drink tube exit hole on top of the backpack. Strap and ring around the backpack, able to add-on pouches and accessories.
1" molle webbing throughout the airsoft backpack. 4 zipper compartments and lots of inside pouches for storing. Adjustable shoulder, chest and waist strap. Hydration system compatible. Hydration system drink tube exit hole on top of the backpack.
A very comfortable nylon made Assault Pack. Thanks to the good planning of the compartment and pocket placing the backpack is very capacious despite the rather small dimensions. The suspenders are adjustable in two ways: on the height of the shoulder and by the bottom of the backpack. The backpack can be taken off in a very easy and fast way thanks to...
LED Module can change your Hopup chamber to be a tracer unit, No silencer type tracer unit anymore, shot illuminated BB without losing balance of weapon. Suitable for MADBULL Ultimate 3-in-1 Hop Up Chamber Unit
Madbull PWS Diablo Compensator -- Primary Weapons Systems, Inc (PWS) is a Federally-licensed firearms manufacturer -- T6 6061 Aluminum Construction
Subcategories
There are 171 products.
Active filters
Fuse - 1 pcs.- 25 amp. It rarely needs replacing, but this small part protects the motor from burning out in case of mechanical problems.
Fuse - 1 pcs.- 25 amp. It rarely needs replacing, but this small part protects the motor from burning out in case of mechanical problems.
Set of 2.8x0.5 Flat Connectors [Female + Male]Two sets of flat connectors intended for installation in wiring or the motor of an AEG replica. The set includes 2 pairs of heat-shrink tubings.
Shim Set: 6x 0,2mm, 6x 0,3mm, 6x 0,5mm
Airsoft AEG Upgrade Part Series, Gearbox Spring for Version 2. Reversal Stop Latch Spring, Tappet Spring, Cover Spring, Cutoff Lever Spring, Switch Spring
SHS Airsoft AEG Upgrade Part Series -- Gearbox Spring for Version 3
Weight: 5 g Material: steel code BD1077
Hop-Up Bucking for Tuned Replicas The Hop-Up bucking was made from silicon, which causes it to retain its quality in low temperatures, because it does not harden as is the case with ordinary rubber buckings. This model performs best in replicas with increased muzzle velocity.
Double Seal Purpose: M4 Replicas Material: Aluminium Length: 21,4mm Manufacturer: Super Shooter/SHS
A set of mounting pins for the MP5 replica's body. Manufacturer: CYMA Weight: 2g Material: aluminum Number of pieces in the set: 2 Length mm: 29 Diameter mm: 6/8.4 Gun model: MP5
Guarder airsoft hop up bucking improve shooting accuracy, ballistic trajectory stability, air-tightness & firmness. Constructed of Silica Gel that is hard.
Includes Bucking 70 Degrees Of Hardness For Marui Style AEG Barrels
Tappet plate for V.2 gearbox
Pack of washers, manufactured by Guarder in steel, indicated for gear adjustments. Indicated for Marui AEG. A set of gearbox shims of different diameters and thicknesses. The set includes per six 0,15mm, 0,30mm and 0,50mm diameter pads. The shims are used to balance the level of the thread-wheels in the gearbox and, what is followed by it, for the most...
G36 Replica Pin Steel assembly pin for G36 replicas.
High-quality polymer tappet plate. It is the ideal solution if the tappet plate in your replica is damaged or worn out. CAUTION! Installation requires experience and manual skills. If you decide on a personal installation you must remember that your warranty will be canceled.
High-quality tappet plate for V2 gearbox. This material can withstand much more than plastic or ABS. It is flexible and resistant to impact. The installation of this component ensures reliable operation of the switch, the type of fire. CAUTION! Installation requires experience and manual skills. If you decide on a personal installation you must remember...
The pin is designed for the body of the G36 type replicas.
Switch V.2 NB0027 A basic replacement of the trigger block - this piece consists of just the sliding contact & the trigger contact block; there is no wiring included. This is only for V2 gearboxes e.g. MP5, M4, M16 etc.
SHS Piston Full Steel 3 Teeth for Gearbox V2, V3