![](https://airsoftguns.ie/19699-large_default/mosfet-gearbox-v2-blue-cyma-.jpg)
Z Tactical Comtac I Headset
The Comtac headset is a double-earpiece communications interface with output sound in both ear and a microphone on an adjustable boom.
The Comtac headset is a double-earpiece communications interface with output sound in both ear and a microphone on an adjustable boom.
Double rifle gun case have two main pockets, bigger one have 120 cm long and shorter one have 93 cm long. It also can be used as backpack. Longer pocket have also a sleeve inside that can extend gun case for extra 27 cm.
The gun bag is made of nylon. Thanks to the application of the additional sleeve the cover will without any problem hold a gun that is up to 1300mm long. Inside of the main chamber there are two additional gun mounting bands. Inside the front 620x260mm big pocket we will fit a machinegun. The gun mounting bands are also located in it.
Gun case with two chambers for dual storage/transportation. Main chamber will hold rifle up to 960 mm long (or 1100 mm when utilising the external hood).Secondary chamber will hold a firearm up to 650 mm long.Case also has pockets that allow transporting magazine or other accesories.Case may be transported in ordinary fasion with use of transport handle...
The bag is constructed from durable and tough 600D nylon, which is capable of supporting the weight of two Airsoft weapons with ease. This practical carry case is ideal for any Airsofter who likes taking more than one Airsoft weapon to a skirmish, and keeping all of their gear together in one convenient bag.
Hydration system drink tube exit hole on top of the backpack. Strap and ring around the backpack, able to add-on pouches and accessories.
A very comfortable nylon made Assault Pack. Thanks to the good planning of the compartment and pocket placing the backpack is very capacious despite the rather small dimensions. The suspenders are adjustable in two ways: on the height of the shoulder and by the bottom of the backpack. The backpack can be taken off in a very easy and fast way thanks to...
Gun case with two chambers for guns. Main chamber will hold gun with lenght up to 800 mm (or 1100 mm with use of external hood) Secondary chamber will hold gun with lenght up to 580 mmCase has also pocket"s allowing for transport of magazine"s or other accesories
LED Module can change your Hopup chamber to be a tracer unit, No silencer type tracer unit anymore, shot illuminated BB without losing balance of weapon. Suitable for MADBULL Ultimate 3-in-1 Hop Up Chamber Unit
Madbull PWS Diablo Compensator -- Primary Weapons Systems, Inc (PWS) is a Federally-licensed firearms manufacturer -- T6 6061 Aluminum Construction
A complete V2 gearbox from the BLUE seriesequipped with a MOSFET system.
It is a complete gearbox ready for installation in the replica. It is equipped with metal gears, a polymer piston with a full rack,piston head and silent aluminum cylinder. Bearings with a diameter of 8 mm are mounted in the gearbox shell.
The mosfet system is equipped with an electronic trigger.
It has a quick spring change system.
The cylinder is made of anodized aluminum, resistant to abrasion and perfectly dissipates the heat generated during the operation of the piston.
The set also includes a powerful motor with neodymium magnets.
A complete V2 gearbox from the BLUE seriesequipped with a MOSFET system.
It is a complete gearbox ready for installation in the replica. It is equipped with metal gears, a polymer piston with a full rack,piston head and silent aluminum cylinder. Bearings with a diameter of 8 mm are mounted in the gearbox shell.
The mosfet system is equipped with an electronic trigger.
It has a quick spring change system.
The cylinder is made of anodized aluminum, resistant to abrasion and perfectly dissipates the heat generated during the operation of the piston.
The set also includes a powerful motor with neodymium magnets.
Weight: 660 g
Bearings type: steel ball-bearing
Gearbox version: v.2
Bearings diameter: 8 mm
CAUTION! If you decide to personal installation gearbox parts as gears, pistons, springs, etc., you must remember that your warranty will be canceled.
Complete, assembled gearbox with the engine, trigger switch and wiring for P90 replicas. Dedicated to 60 cyma replicas. CAUTION! If you decide to personal installation gearbox parts as gears, pistons, springs, etc., you must remember that your warranty will be cancelled. Weight: 730 g
CYMA V3 gearbox is a complete drop-in gearbox solution for those who are looking for a powerful, durable yet economical complete V3 full metal gearbox. Complete GB with a new series of replicas CM.040, 045, 048
Gearbox type V2 with reinforced construction. The front part has been strengthened, the most exposed to damage has been considerably thickened, and the place of the contact with the cylinder has been improved so as to evenly transfer the loads. It is prepared for mounting 8mm bearings. Mounting this gearbox to replicas of other manufacturers than J.G. ,...
Weight: 375 g Material: aluminum color black
Metal trigger pin for M4, M16 series and similar replicas. It may require shortening to fit perfectly with your replica. Weight: 2 g Material: steel Length: 29 mm
Completed Gearbox set ready to upgrade Come With Motor The spring 115 used in the gearbox will give you +/- 380 FPS - depend on the barrel and hop-up unit, used in your replica. Essential part for upgrading your Airsoft Electric Gun AEG To build a tight & durable gearbox Compatible with Tokyo Marui, JG, AGM, CM - M4/M16. 8mm Bearing Enhanced Gearbox...
COMPLETE CYMA Enhanced Version 3 (V3) Full Metal Gearbox & High Torque Motor Weight: 745 g Gearbox version: v.3 Bearings diameter: 7 mm
G36 Replica Pin Steel assembly pin for G36 replicas.
The reinforced complete V2 version gearbox was designed to be mounted in the M4 replica series. It is a perfect solution for those who want to buy a good gearbox in a reasonable price. The gearbox's frame was adapted to mount 7mm bearings and the V3 version allows to use it in the M4/M16 family carbine replicas.
WELL Trigger Assembly Suitable for airsoft Type 96 series by WELL MB-01 / SD96 / UTG Type 96 Shadow Ops / Bravo / Double Eagle / Maruzen and other compatible airsoft bolt action sniper rifles. Steel made upgrade part.
The catch is ambidextrous so can be installed for either left or right handed shooters, is made of sterner materials than some stock mag catches and has a strong but purposeful feedback to the action. Making sure you have replacement parts on hand can avoid tactical blunders in the field so don't hesitate to get supply of replacement parts, especially...
The pin is designed for the body of the G36 type replicas.
A complete V2 gearbox from the BLUE seriesequipped with a MOSFET system.
It is a complete gearbox ready for installation in the replica. It is equipped with metal gears, a polymer piston with a full rack,piston head and silent aluminum cylinder. Bearings with a diameter of 8 mm are mounted in the gearbox shell.
The mosfet system is equipped with an electronic trigger.
It has a quick spring change system.
The cylinder is made of anodized aluminum, resistant to abrasion and perfectly dissipates the heat generated during the operation of the piston.
The set also includes a powerful motor with neodymium magnets.